Torque Calculator — Convert speed, pace, and travel-time estimates

This torque calculator evaluates rotational moment using either force, lever distance, and application angle or mechanical power and shaft speed. It converts supported inputs to SI units, displays the result in several torque units, and exposes the intermediate quantities needed to audit the calculation. Use it for physics problems, preliminary mechanism design, motor comparisons, and workshop estimates—not as a substitute for certified engineering analysis.

How to use

Choose the calculation method that matches the information you actually have. Select “Force and lever arm” when you know an applied force and its geometry. Enter Force, choose N, kN, lbf, or kgf, and enter Distance from pivot using the distance unit shown. Enter the Angle between lever arm and force. Use 90 degrees when the force is perpendicular to the lever. If your angle is measured from the perpendicular rather than from the lever, convert it to the required included angle first.

Choose “Power and rotational speed” when you know mechanical shaft power and speed at the same operating point. Enter Mechanical power and select W, kW, or mechanical hp. Enter Rotational speed in rpm or rad/s. RPM is converted internally using $\omega=2\pi n/60$. Speed must exceed zero because division by zero cannot produce torque from power.

Use “Display torque in” to choose N·m, kN·m, lbf·ft, lbf·in, or kgf·m. The main result changes units without changing the underlying torque. Review the SI torque and the intermediate quantities beneath it. In force mode these show perpendicular force and lever distance; in power mode they show watts and angular velocity. This breakdown is useful for detecting unit or angle mistakes.

Use “Reset values” to restore the worked defaults. The calculator updates whenever an input or unit changes. If a field is empty, negative where inappropriate, or non-finite, it is identified beside the input and the result is withheld. Before using an answer in engineering work, confirm the axis, angle convention, power definition, measurement precision, losses, duty cycle, and relevant safety factors.

Formula

$$\tau=rF\sin(\theta)=Fd_{\perp}$$ $$F_{\perp}=F\sin(\theta)$$ $$\tau=\frac{P}{\omega},\qquad \omega=\frac{2\pi n}{60}$$ where $\tau$ is torque in N·m, $r$ is lever distance in m, $F$ is force in N, $\theta$ is the angle between the lever arm and force, $d_{\perp}$ is perpendicular moment arm, $P$ is mechanical power in W, $\omega$ is angular velocity in rad/s, and $n$ is rotational speed in rpm.

Step by step

Worked force audit: let $F=250\,\mathrm{N}$, $r=0.40\,\mathrm{m}$, and $\theta=35^\circ$. Convert the angle for the sine evaluation: $35^\circ\times\pi/180=0.610865\,\mathrm{rad}$. Find the effective perpendicular force: $F_{\perp}=250\sin(35^\circ)=143.394\,\mathrm{N}$. Multiply by lever distance: $\tau=0.40\times143.394=57.3576\,\mathrm{N\cdot m}$. Convert to pound-force feet using 1 lbf·ft = 1.355817948 N·m: $57.3576/1.355817948=42.3048\,\mathrm{lbf\cdot ft}$. Reasonableness check: the maximum at 90° would be $0.40\times250=100\,\mathrm{N\cdot m}$, so 57.36 N·m at 35° is plausible.

Worked power audit: let $P=7.5\,\mathrm{kW}=7500\,\mathrm{W}$ and $n=1800\,\mathrm{rpm}$. Convert speed: $\omega=2\pi(1800)/60=188.4956\,\mathrm{rad/s}$. Divide power by angular velocity: $\tau=7500/188.4956=39.7887\,\mathrm{N\cdot m}$. Substitution check gives $39.7887\times188.4956\approx7500\,\mathrm{W}$, recovering the stated mechanical power.

Detailed calculation guide

A torque calculator finds the turning effect of a force about an axis. For a force applied along a lever, torque magnitude is the force multiplied by lever distance and the sine of their included angle. For a rotating shaft, torque is mechanical power divided by angular velocity. This tool performs the required unit conversions, reports newton-metres, and converts the same result to common metric and customary torque units.

Torque is calculated with $\tau=rF\sin(\theta)$, where $r$ is pivot-to-application distance, $F$ is force, and $\theta$ is the angle between them. With shaft power, use $\tau=P/\omega$ and convert RPM through $\omega=2\pi n/60$. A perpendicular force has $\theta=90^\circ$ and produces the maximum torque for fixed $r$ and $F$.

Torque describes how strongly a force tends to rotate an object around a chosen point or axis. It is also called the moment of force. The axis matters: the same force can create a large torque about one pivot and no torque about another. Torque is therefore not a property of the force alone. It depends on the force magnitude, its line of action, and the reference axis.

The force-and-lever method implements the magnitude of the vector cross product $\boldsymbol{\tau}=\mathbf{r}\times\mathbf{F}$. Its scalar magnitude is $\tau=rF\sin(\theta)$. The vector $\mathbf{r}$ runs from the rotation axis to the point where the force is applied. The included angle is measured from that lever-arm vector to the force vector. Only the component perpendicular to the lever contributes: $F_\perp=F\sin(\theta)$. Equivalently, torque equals the force multiplied by the shortest perpendicular distance from the axis to the force's line of action.

The angle convention is crucial. A force at $90^\circ$ to the lever has $\sin(90^\circ)=1$, so the entire force is effective. A force parallel or antiparallel to the lever has a line of action through the pivot; its sine is zero and it creates no torque about that pivot. Angles beyond $180^\circ$ can reverse rotational direction. Because this calculator reports magnitude, it takes the absolute value after evaluating the sine. A signed calculation requires a declared positive axis or clockwise/counterclockwise convention.

The power-and-speed method follows $P=\tau\omega$ for rotational mechanical power. Rearrangement gives $\tau=P/\omega$. Angular velocity must be expressed in radians per second, not revolutions per minute. For speed $n$ in RPM, $\omega=2\pi n/60$. This distinction explains the familiar engineering shortcut $\tau\,[\mathrm{N\cdot m}]\approx9550P\,[\mathrm{kW}]/n\,[\mathrm{rpm}]$. The shortcut is rounded; the calculator evaluates the full expression.

Torque units deserve careful notation. The SI unit is the newton-metre, written N·m. One kilonewton-metre is 1,000 N·m. NIST conversion factors imply approximately 1 lbf·ft = 1.355818 N·m, 1 lbf·in = 0.1129848 N·m, and 1 kgf·m = 9.80665 N·m. Pound-force foot identifies force explicitly and is preferable to ambiguous expressions such as “lb-ft.” The software keeps an unrounded N·m value internally and converts only for display.

Although N·m has the same SI base dimensions as the joule, torque and energy are not interchangeable concepts. Torque is an axial or pseudovector quantity associated with a turning tendency. Work is a scalar obtained by integrating force through displacement; rotational work is obtained by integrating torque through angular displacement. Reporting torque in joules hides this physical distinction, so established SI practice retains N·m for torque.

Common Mistakes

  • Multiplying the complete lever length by force when the force is angled. Use the perpendicular force component or perpendicular moment arm.
  • Measuring the angle from the perpendicular while entering it as though measured from the lever. If the provided angle is measured from the perpendicular, its complement is required.
  • Entering kilograms as force. Kilograms measure mass; a stationary hanging mass produces an approximate weight $F=mg$ under a stated gravitational acceleration.
  • Mixing millimetres with metres or kilonewtons with newtons. A 250 mm handle is 0.250 m, and 3 kN is 3,000 N.
  • Substituting RPM directly into $P=\tau\omega$. RPM must first become rad/s.
  • Using electrical input power as mechanical output power without efficiency losses.
  • Assuming rated or peak motor torque is available throughout the operating-speed range.
  • Treating a static torque estimate as a bolt-tightening specification or structural safety approval.

Assumptions

The force mode assumes a rigid lever, a clearly defined axis, and a concentrated force whose line of action and angle are known. It calculates one force contribution at a time. If several forces act, their vector torques must be assigned signs and summed. The power mode assumes the entered power is instantaneous mechanical shaft power at the same location and time as the entered speed. It also assumes a meaningful nonzero angular velocity and neglects transient energy stored in rotating inertia.

Unit conversion assumes standard definitions. Kilogram-force uses standard gravity, 9.80665 m/s². Horsepower can have multiple definitions; this calculator uses mechanical horsepower, approximately 745.6999 W. Users working with metric horsepower, boiler horsepower, or manufacturer-specific ratings must convert the stated rating independently. Display rounding does not imply measurement accuracy.

Limitations

A scalar calculator cannot determine the three-dimensional torque vector, axis direction, bearing reactions, bending stress, shear stress, shaft twist, fatigue life, or factor of safety. It does not model a distributed force, flexible member, changing geometry, friction, backlash, gear efficiency, belt slip, clutch losses, or speed-dependent motor behavior. It also cannot infer whether a force value is peak, RMS, average, or static.

At zero rotational speed, finite torque can exist but the equation $\tau=P/\omega$ cannot recover it from power because both mechanical power and angular velocity may be zero. Stall torque must come from a motor curve, test data, or an appropriate electromagnetic model. Near zero speed, small errors in speed or power can create very large relative error in calculated torque.

Practical Applications

The force mode helps evaluate hand tools, pedals, cranks, hinges, levers, steering mechanisms, robot joints, valve handles, and laboratory statics problems. The power mode helps compare motors, engines, turbines, gearboxes, conveyors, pumps, and rotating machinery at a stated operating point. Educators can use both modes to show why geometry controls moment and why identical power ratings can correspond to different torque at different speeds.

For a gearbox, calculate input and output locations separately. In an ideal reduction gearbox, lower output speed corresponds to proportionally greater output torque while power stays constant. A real gearbox delivers less output power because of losses. If efficiency $\eta$ is known, a simplified steady estimate is $\tau_{out}=\eta P_{in}/\omega_{out}$, not merely $P_{in}/\omega_{out}$.

Tips

Sketch the pivot, lever vector, and force arrow before entering numbers. Mark the included angle explicitly. When possible, measure the shortest perpendicular distance to the line of action; then use $\tau=Fd_\perp$ and avoid angle ambiguity. Keep several extra significant figures through intermediate conversions. Round the final result to match the least precise measured input rather than copying every displayed digit.

For power calculations, confirm whether a datasheet quotes input power, shaft output power, continuous power, or peak power. Pair power and RPM from the same operating point on the same performance curve. A maximum-power value combined with a minimum-speed value from another condition can produce a torque figure that the machine never develops.

Interpretation

A larger torque magnitude means a stronger instantaneous turning tendency about the selected axis, but it does not automatically mean faster rotation. Angular acceleration follows the rotational analogue of Newton's second law: net torque equals moment of inertia times angular acceleration for a rigid body about a fixed principal axis. A system with high rotational inertia may accelerate slowly despite substantial torque.

In the force mode, the perpendicular-force result shows how much of the applied force actually contributes to the moment. The displayed lever distance remains the full pivot-to-application distance. In the power mode, the angular-velocity result provides the essential conversion audit. If torque looks unexpectedly high, verify that RPM was not confused with rad/s and that power and speed describe the same shaft.

Related Formulas

  • Perpendicular force component: $F_\perp=F\sin(\theta)$.
  • Perpendicular moment arm: $d_\perp=r\sin(\theta)$.
  • Moment from perpendicular distance: $\tau=Fd_\perp$.
  • Rotational power: $P=\tau\omega$.
  • RPM conversion: $\omega=2\pi n/60$.
  • Rigid-body angular acceleration: $\alpha=\tau_{net}/I$.
  • Rotational work for constant torque: $W=\tau\Delta\phi$.
  • Ideal gear relation: $\tau_{out}/\tau_{in}=\omega_{in}/\omega_{out}$.

Best Practices

Define the axis and sign convention before combining torques. Convert all quantities to a coherent unit system, calculate without premature rounding, and preserve an audit trail of original values and conversion factors. Separate measured data from assumed data. Include uncertainty when measurements control a consequential design. Check the result with dimensional analysis and an order-of-magnitude estimate; doubling force or distance should double torque, while halving speed at fixed power should double torque.

For engineering work, compare calculated loads with component ratings only after accounting for service factors, duty cycle, shock, temperature, tolerances, fatigue, and applicable codes. Torque-tool settings, motor ratings, and fastener specifications may use different definitions and test conditions. A numerical match alone does not establish compatibility.

When NOT to use this calculator

Do not use this calculator as the sole basis for lifting equipment, pressure-boundary components, vehicle controls, medical devices, aviation hardware, human-safety restraints, or other safety-critical designs. Do not use the power mode for stall torque, rapidly accelerating systems, or mismatched power and speed measurements. Do not use a simple lever calculation where the member deforms enough to change geometry or where contact forces are distributed and unknown.

For fastener tightening, the applied wrench torque is not a direct measurement of bolt preload. Thread friction, under-head friction, lubrication, coatings, reuse, and joint stiffness strongly affect the relationship. Follow the equipment or fastener manufacturer's procedure and use calibrated tools where required.

Real-world examples

A mechanic applying 200 N perpendicular to a 0.30 m breaker bar produces 60 N·m about the fastener. Pulling at 30° to the bar produces only 30 N·m because only half the force is perpendicular. The comparison demonstrates why pulling direction matters as much as handle length.

A 5 kW shaft at 1,500 RPM has angular velocity about 157.08 rad/s and torque about 31.83 N·m. If the same mechanical power is available at 750 RPM, torque doubles to about 63.66 N·m. Real machines may not maintain constant power across those speeds, so performance curves remain authoritative.

A 10 kg mass suspended from a horizontal 0.40 m arm is not entered as 10 N. Under standard gravity its weight is 98.0665 N, giving approximately 39.23 N·m when the force is perpendicular. Local gravity and dynamic motion may alter the actual load.

Comparison and educational intent

Force-distance calculation answers a geometry question: how effectively does an applied force act about an axis? Power-speed calculation answers an operating-point question: what torque corresponds to a stated transfer of mechanical energy at a stated angular speed? They can describe the same shaft or mechanism, but they rely on different measured information and should not be mixed casually.

This Torque Calculator is designed to make those distinctions visible through intermediate SI values and explicit formulas. Its result is most useful as a transparent estimate that can be independently reproduced. For classroom work, show the conversions and significant figures. For design work, supplement the estimate with free-body diagrams, performance data, uncertainty analysis, component standards, and qualified engineering review.

Beginner: perpendicular wrench force

60 N·m

A perpendicular force uses the entire 0.30 m lever arm, so torque is 0.30 × 200 × sin(90°) = 60 N·m.

Intermediate: angled force on a lever

Approximately 57.3576 N·m

The effective perpendicular force is about 143.394 N. Multiplying it by 0.40 m gives approximately 57.3576 N·m.

Advanced: motor torque from power and RPM

Approximately 39.7887 N·m

The calculator converts 1,800 rpm to 188.4956 rad/s and divides 7,500 W by that angular velocity.

Edge case: force directed through the pivot

0 N·m

Despite the large force and distance, the line of action passes through the pivot, so the perpendicular component and torque are zero.

Real-world: imperial breaker bar

150 lbf·ft

An 18-inch lever is 1.5 feet. A perpendicular 100 lbf force therefore produces 100 × 1.5 = 150 lbf·ft.

Power-speed comparison at low RPM

Approximately 63.662 N·m

At 750 rpm, angular velocity is about 78.5398 rad/s. Dividing 5,000 W by that value gives approximately 63.662 N·m.

Frequently asked questions

How do I calculate torque from force and distance?

Multiply force by the perpendicular distance from the axis to the force's line of action. If you know the full lever distance and included angle, use $\tau=rF\sin(\theta)$. Keep force in newtons and distance in metres for N·m.

What angle should I enter for a perpendicular force?

Enter 90 degrees when the angle is defined between the lever arm and force. Its sine equals one, so the force produces the maximum torque possible for that force magnitude and lever distance.

How do I calculate torque from power and RPM?

Convert RPM to radians per second with $\omega=2\pi n/60$, then divide mechanical power in watts by angular velocity: $\tau=P/\omega$. Power and RPM must describe the same shaft and operating point.

How many newton-metres are in one pound-force foot?

Using the NIST conversion factor, 1 pound-force foot is approximately 1.355818 newton-metres. To convert N·m to lbf·ft, divide by approximately 1.355818.

Are N·m and joules the same thing?

No. They share the same SI base dimensions, but torque represents a turning moment and energy represents scalar work. Torque should be written in newton-metres, while energy is normally written in joules.

Can I enter kilograms in a torque calculator?

Kilograms measure mass, not force. Convert a mass to weight with $F=mg$ before using it. Under standard gravity, one kilogram produces 9.80665 N of weight, but actual acceleration and local gravity may differ.

Why is torque zero when the force points toward the pivot?

The force's line of action passes through the rotation axis, so the perpendicular moment arm is zero. In angular form, the included angle is 0° or 180° and its sine is zero.

Does higher RPM always mean more torque?

No. At fixed mechanical power, torque decreases as angular speed increases. Real motors do not necessarily operate at fixed power, and their torque varies with speed, control strategy, temperature, voltage, and loading.

What is the difference between torque and moment of force?

In elementary mechanics, both terms describe the rotational effect of a force about a point or axis. Engineering usage may prefer “moment” for structural statics and “torque” for twisting shafts, but the governing cross-product concept is the same.

Why does an angled force produce less torque?

Only the component perpendicular to the lever arm contributes to torque. That component is $F\sin(\theta)$. The parallel component points along the lever and does not create a moment about the selected pivot.

Can this calculator determine bolt-tightening preload?

Not reliably. Applied tightening torque is strongly affected by thread friction, bearing-surface friction, lubrication, coatings, geometry, and tool accuracy. Use the manufacturer's fastening procedure and applicable engineering standards.

Can I calculate motor stall torque from power and RPM?

No. At stall, angular velocity and mechanical output power are both zero, so dividing power by speed is indeterminate. Obtain stall torque from verified motor data, testing, or an appropriate motor model.

Related calculators

Browse all calculators in this category

Editorial review

Author: JD

Sources

Enable JavaScript to use interactive calculators.