Segment Perimeter Calculator — Free online Segment Perimeter Calculator with instant, explainable results

This Segment Perimeter Calculator finds the complete boundary of a circular segment—not merely its curved arc. Enter a radius and angle, radius and chord, radius and segment height, or chord and height. The calculator derives the missing geometry, distinguishes minor and major segments, and reports the perimeter, arc, chord, angle, radius, and sagitta in consistent units.

How to use

Select the Input method that matches your known measurements. For Radius and central angle, enter Radius and Central angle, then choose Degrees or Radians under Angle unit. Any angle greater than zero and less than one full turn is accepted; an angle above 180 degrees or π radians represents a major segment.

For Radius and chord length, enter both measurements and use Segment type to choose the shorter minor arc or longer major arc. The chord must not exceed twice the radius. For Radius and segment height, enter the sagitta as the perpendicular distance from the chord to the selected arc. A height below the radius identifies a minor segment, while a height above the radius identifies a major segment.

Choose Chord length and segment height when the circle’s centre or radius is unavailable. Measure the chord in a straight line between the arc endpoints. Measure Segment height at the chord midpoint and perpendicular to it. The calculator will infer the supporting circle’s radius and central angle.

Choose a Length unit that applies to every length value; the selector does not convert numbers entered in different units. Select the desired Decimal places for display. Results update immediately whenever a field changes. Read Segment perimeter for the total curved-plus-straight boundary. Use Arc length when only the curved edge is needed, and Chord length when only the closing straight edge is needed. Check the angle, segment classification, derived height or radius, and equation line before transferring the result. Use Reset values to restore the default 10-unit radius and 60-degree example.

Formula

$$P=L+c=r\theta+2r\sin\left(\frac{\theta}{2}\right)$$ $$\theta_{\text{minor}}=2\arcsin\left(\frac{c}{2r}\right),\qquad \theta_{\text{major}}=2\pi-\theta_{\text{minor}}$$ $$\theta=2\arccos\left(\frac{r-h}{r}\right),\qquad c=2\sqrt{2rh-h^2}$$ $$r=\frac{c^2+4h^2}{8h},\qquad \theta=4\arctan\left(\frac{2h}{c}\right)$$ $$\theta_{\text{rad}}=\theta_{\text{deg}}\frac{\pi}{180}$$

Step by step

Worked audit using radius r = 10 cm and central angle 60°:

  1. Convert the angle to radians: θ = 60 × π/180 = π/3 ≈ 1.047197551 radians.
  2. Calculate the arc length: L = rθ = 10 × 1.047197551 = 10.471975512 cm.
  3. Calculate the chord: c = 2r sin(θ/2) = 20 sin(π/6) = 10 cm.
  4. Add the two boundary components: P = L + c = 10.471975512 + 10 = 20.471975512 cm.
  5. Calculate the sagitta as a check: h = r(1 − cos(θ/2)) = 10(1 − cos 30°) ≈ 1.339745962 cm.
  6. Interpret the result: 60° is below 180°, so this is a minor segment. The arc occupies 60/360 = 16.6667% of the full circumference. Rounded to four decimal places, the segment perimeter is 20.4720 cm.

Detailed calculation guide

A Segment Perimeter Calculator determines the boundary length of the region cut from a circle by a straight chord. It calculates the selected arc, calculates or retains the chord, and adds those two lengths. You can start with several practical measurement pairs, including radius and angle, radius and chord, radius and height, or chord and height. The result keeps the same length unit used for the inputs.

A circular segment is the region bounded by one chord and its corresponding circular arc. Its perimeter is therefore the chord length plus the selected arc length. It is not the same as a sector perimeter: a sector uses an arc and two radii, whereas a segment replaces those radii with one straight chord.

Geometry and terminology

Every non-diameter chord divides a circle into two circular segments. The minor segment uses the shorter arc and has a central angle below 180 degrees. The major segment uses the longer arc and has a central angle above 180 degrees. When the chord is a diameter, the two regions are semicircular segments and each angle is exactly 180 degrees.

The radius, written as r, is the distance from the circle’s centre to its circumference. The chord, c, joins the two endpoints of the selected arc. The central angle, θ, is measured between radii drawn to those endpoints. The segment height, h, is the maximum perpendicular distance from the chord to the selected arc; it is also called the sagitta.

Segment height deserves careful interpretation. For a minor segment, the height lies between zero and the radius. A semicircular segment has h = r. A major segment has a height greater than r but less than 2r because the measured distance crosses past the circle’s centre toward the longer arc. This convention lets radius and height identify the intended segment without a separate minor-or-major choice.

Core perimeter method

When radius and central angle are known, θ must first be expressed in radians. Arc length is rθ because one radian subtends an arc equal in length to the radius. The chord is 2r sin(θ/2). Adding the boundary components gives P = rθ + 2r sin(θ/2).

Degrees cannot be inserted directly into that expression. Convert an angle α in degrees using θ = απ/180. For example, 60 degrees becomes π/3 radians. The calculator performs this conversion internally when Degrees is selected and also displays both representations so the audit trail remains visible.

The same chord belongs to two arcs. If r and c are supplied, the minor angle is 2 asin(c/(2r)). The major angle is 2π minus that minor angle. The chord cannot exceed 2r; a longer chord would exceed the circle’s diameter and cannot exist in Euclidean circle geometry. At c = 2r, both selections meet at θ = π.

With radius and segment height, the angle is θ = 2 acos((r − h)/r), and the chord is 2√(2rh − h²). These relationships work across minor and major segments when 0 < h < 2r. The inverse-cosine result naturally moves beyond π once h becomes greater than r.

When only chord and height are known, the implied radius is (c² + 4h²)/(8h). The selected central angle can be calculated as 4 atan(2h/c). This form is particularly useful in field measurement because it works with both shallow minor arcs and deep major arcs without requiring the circle’s centre to be located first.

Interpretation

The prominent result is the entire segment boundary. The arc-length line is its curved component, and the chord-length line is its straight component. Their sum should agree with the displayed perimeter apart from the final display rounding. The angle and arc-share outputs indicate whether the chosen boundary follows a small or large portion of the parent circle.

A result labelled “minor segment” follows less than half of the circumference. “Major segment” follows more than half. “Semicircular segment” uses exactly half the circumference plus a diameter. The arc share is θ/(2π), expressed as a percentage; it is a useful reasonableness check but is not a percentage of the segment perimeter because the chord is also part of that perimeter.

The derived height is measured to the selected arc, not necessarily to the nearest side of the circumference. This distinction is important for major segments. Likewise, a derived radius is the radius of the complete supporting circle, even if only a small arc is present in the physical object.

Common Mistakes

  • Using the sector formula rθ + 2r. That boundary includes two radii and answers a different question.
  • Reporting rθ alone. Arc length is only the curved component; a segment perimeter must also include its chord.
  • Passing degrees to a sine, cosine, or arc-length expression designed for radians.
  • Choosing a minor arc automatically when the drawing, workpiece, or specification requires the major arc.
  • Treating segment height as the perpendicular distance from the chord to the centre. Sagitta is measured from the chord to the selected arc.
  • Mixing units, such as entering a radius in centimetres and a chord in millimetres.
  • Entering a chord greater than the diameter or a height at least twice the radius.
  • Rounding the derived angle before calculating the arc. Early rounding can be magnified when the radius is large.
  • Assuming a large central angle produces a negative chord. The chord formula remains positive for every angle between 0 and 2π.

Assumptions

The calculator assumes an ideal Euclidean circle, a straight chord, and measurements referring to the same circular profile. All length entries are assumed to use the unit selected in the interface. The unit selector labels rather than converts the measurements; changing from centimetres to inches does not numerically convert values already entered.

Angles must be greater than zero and less than one complete turn. This open interval excludes a collapsed zero-length arc and the degenerate case in which both arc endpoints coincide after a full revolution. Radius, chord, and height measurements must be positive. The calculation retains full JavaScript floating-point precision internally and rounds only the displayed outputs.

The chord-height method assumes the height was measured perpendicular to the chord at its midpoint. For a true circular arc, that perpendicular line passes through the circle’s centre. An off-centre rise measurement does not satisfy the sagitta formula and can produce a misleading implied radius.

Limitations

Real objects may not be perfectly circular. Bent sheet metal, road curves, arches, pipes, lenses, and machined profiles can depart from a mathematical circle because of manufacturing tolerance, wear, thermal movement, or measurement error. Two input measurements may still force an exact circular solution even when the actual profile varies along its length.

Near-degenerate measurements require additional care. A very small height compared with a long chord implies a very large radius. Small absolute measurement errors in that height can then cause substantial changes in the calculated radius and arc length. At the other extreme, a height approaching twice the radius describes an arc approaching a full circle while its chord approaches zero. Ordinary measuring equipment may not resolve that geometry reliably.

This tool calculates boundary length, not area, centroid, bending allowance, material stretch, kerf, seam allowance, surface area, or three-dimensional volume. It does not replace tolerance analysis or a project-specific engineering model. Displayed precision indicates formatting, not guaranteed measurement accuracy.

Practical Applications

Circular-segment perimeter appears in geometry exercises, architectural arches, window and door heads, curved edging, landscaping borders, road and rail alignment sketches, sheet-metal layouts, machining inspections, tanks, pipe openings, and decorative fabrication. It can estimate the length of trim around a segment-shaped panel when both the curved edge and closing straight edge require material.

In education, the multiple input methods reveal how inverse trigonometric relationships connect radius, chord, sagitta, and central angle. A teacher can hold the chord constant, switch between minor and major arcs, and demonstrate why the same endpoints do not uniquely specify an arc. Students can also compare arc share with the central angle’s share of a complete revolution.

For inspection work, chord and height are often easier to measure than radius because the circle’s centre may be inaccessible or far outside the workpiece. The resulting radius is useful as a geometric inference, but its uncertainty should be evaluated from the uncertainty of both field measurements.

Tips

  • Sketch the circle, chord, selected arc, and height before entering values.
  • Decide whether the desired boundary follows the shorter or longer arc.
  • Use one unit throughout and convert measurements before calculation if necessary.
  • Measure sagitta at the chord midpoint and perpendicular to the chord.
  • Increase displayed decimal places for auditing, then round the final result to measurement-appropriate precision.
  • Compare the chord with 2r and the height with 2r before relying on the result.
  • Preserve the calculator’s unrounded intermediate values when transferring results into a larger workflow.

Related Formulas

The full circumference is C = 2πr. The selected arc length is L = rθ, and its fraction of the circumference is θ/(2π). The chord is c = 2r sin(θ/2). Segment height is h = r(1 − cos(θ/2)). These formulas use the angle of the selected segment, so a major angle produces a major height.

The area of a minor circular segment is A = r²(θ − sin θ)/2 when θ is in radians. For a major segment, that same signed-angle expression can be used with the major angle, or the minor-segment area can be subtracted from πr². Area is related to the same geometry but has square units and must not be added to perimeter.

For a semicircular segment, θ = π, c = 2r, and P = πr + 2r = r(π + 2). This provides a convenient benchmark. For a very small angle, the chord and arc are nearly equal, so the segment perimeter approaches approximately twice the arc length.

Best Practices

Record both original inputs and the input method with any result. A bare perimeter is difficult to audit because different segment geometries can share similar boundary lengths. Retain the calculated radius, angle, arc, chord, and height as supporting values. They make transcription mistakes and wrong-arc selections easier to detect.

Match output precision to input quality. Measurements recorded to the nearest millimetre do not justify a fabrication claim at micrometre precision merely because six decimal places are displayed. For consequential work, calculate a range using plausible minimum and maximum measurements or perform a formal uncertainty analysis.

When a drawing supplies radius and angle directly, prefer that pair because it avoids reconstructing the circle from measured sagitta. When the centre is inaccessible, chord and height are usually the most practical alternative. If both theoretical dimensions and field measurements exist, calculate both and investigate discrepancies rather than silently mixing them.

When NOT to use this calculator

Do not use this calculator for an elliptical, parabolic, catenary, spline, or irregular arc. A chord and rise can always imply a circle, but that does not prove the actual curve is circular. Do not use it for a sector boundary, an annular segment with inner and outer arcs, or a three-dimensional spherical segment.

It is also unsuitable as the sole basis for structural safety, legal metrology, high-tolerance machining, medical-device design, or regulated surveying. Those applications require verified instruments, documented tolerances, appropriate standards, and professional review. The calculator can serve as an independent arithmetic check after the correct geometric model has been established.

Real-world examples

Consider an arched opening with radius 8 m and rise 2 m. The height is less than the radius, so it is a minor segment. The derived chord is about 10.583 m, the angle is about 82.819 degrees, and the complete boundary is about 22.147 m. If trim covers only the curved arch, use the arc result rather than the segment perimeter.

A circular panel with radius 5 cm and chord 6 cm illustrates the two-arc ambiguity. Its minor segment has a 73.740-degree angle and a perimeter near 12.435 cm. Selecting the major segment keeps the 6 cm chord but changes the arc to more than 286 degrees, producing a perimeter near 30.981 cm.

For a shallow fabricated curve with a 12 in chord and 3 in rise, the inferred radius is 7.5 in. The angle is about 106.260 degrees, the arc is about 13.909 in, and the boundary is about 25.909 in. Measurements should include allowance for cutting and joining only after this ideal geometric length is established.

Comparison and educational intent

A dedicated segment calculator is more reliable than treating every curved region as a sector. The key conceptual test is the straight part of the boundary: one chord indicates a segment, while two radii indicate a sector. A circumference calculator answers only the full-circle case, and an arc-length calculator omits the closing chord.

The Segment Perimeter Calculator is intended to make that distinction explicit and to expose every derived quantity needed for verification. Its multiple input modes support both textbook data and measurements available in practice. Used with consistent units, the correct arc selection, and realistic precision, it provides a transparent calculation rather than a result that must be accepted without an audit trail.

Beginner: radius and 60-degree angle

Segment perimeter = 20.4720 cm; arc = 10.4720 cm; chord = 10 cm.

The 60-degree minor arc is π/3 radians. Its arc length is 10π/3 cm and its chord is exactly 10 cm, so their sum is approximately 20.4720 cm.

Intermediate: radius and chord for a minor segment

Segment perimeter ≈ 12.4350 cm; central angle ≈ 73.7398°; height = 1 cm.

The chord-to-diameter ratio is 0.6, giving a minor angle of about 1.2870 radians. The arc is about 6.4350 cm, which is added to the 6 cm chord.

Advanced: same radius and chord for a major segment

Segment perimeter ≈ 30.9809 cm; central angle ≈ 286.2602°; height = 9 cm.

The chord remains 6 cm, but the selected angle is 2π minus the minor angle. The much longer major arc produces a perimeter substantially greater than the minor result.

Edge case: semicircular segment

Segment perimeter ≈ 20.5664 m; arc ≈ 12.5664 m; chord = 8 m.

At 180 degrees the chord is the diameter. The perimeter is πr + 2r = 4π + 8, providing a useful check on the general formula.

Real-world: measured chord and rise

Segment perimeter ≈ 25.9094 in; derived radius = 7.5 in; central angle ≈ 106.2602°.

A 12-inch chord and 3-inch midpoint rise imply a 7.5-inch circular radius. The derived arc is approximately 13.9094 inches, which is added to the chord.

Frequently asked questions

What is the perimeter of a circular segment?

The perimeter of a circular segment is the length of its selected circular arc plus the straight chord joining the arc’s endpoints. It does not include two radii. If the arc length is L and the chord length is c, the segment perimeter is P = L + c.

How do I calculate segment perimeter from radius and angle?

Convert the central angle to radians, calculate arc length as rθ, calculate chord length as 2r sin(θ/2), and add them. The combined formula is P = rθ + 2r sin(θ/2), where r is the radius and θ is the selected angle in radians.

Is segment perimeter the same as sector perimeter?

No. A circular segment is bounded by one arc and one chord, so its perimeter is arc plus chord. A circular sector is bounded by one arc and two radii, so its perimeter is arc plus 2r. Confusing these shapes produces a different boundary length.

Can I find segment perimeter from chord and segment height?

Yes. Chord c and height h determine the supporting radius through r = (c² + 4h²)/(8h). They also determine the selected angle through θ = 4 atan(2h/c). The perimeter then equals rθ + c, provided the height is measured perpendicular to the chord at its midpoint.

Why must I choose a minor or major segment?

A chord divides a circle into two regions that share the same straight boundary but follow different arcs. The minor segment uses the shorter arc, while the major segment uses the longer arc. Their chord lengths match, but their arc lengths and perimeters are different.

What is segment height or sagitta?

Segment height, also called sagitta, is the maximum perpendicular distance from the chord to the selected arc. It is measured at the chord’s midpoint. A minor-segment height is below the radius, a semicircular height equals the radius, and a major-segment height exceeds the radius.

Can a circular segment have an angle greater than 180 degrees?

Yes. A central angle greater than 180 degrees and less than 360 degrees describes a major segment. Its boundary follows the longer of the two arcs sharing the chord. The chord formula still works, and the segment height is greater than the circle’s radius.

What happens when the chord equals the diameter?

When c = 2r, the chord passes through the circle’s centre and the segment is semicircular. Its central angle is π radians or 180 degrees, its height equals r, and its perimeter is half the circumference plus the diameter: P = πr + 2r.

Why does the angle need to be in radians?

The direct arc-length identity L = rθ is defined for θ measured in radians. If the angle is supplied in degrees, multiply it by π/180 first. The calculator performs this conversion automatically when Degrees is selected, then shows the degree and radian values for verification.

Does changing the length unit convert my values?

No. The unit selector labels the inputs and outputs; it does not numerically convert existing entries. All length measurements must already use the same unit. Convert mixed measurements before entering them—for example, convert millimetres to centimetres rather than combining both.

Why is a chord longer than twice the radius invalid?

The longest possible chord is a diameter, whose length is 2r. Any proposed chord longer than that cannot fit inside the specified circle. If this error appears, check the measurements, verify the units, or confirm that the stated radius belongs to the same circular arc.

How accurate is the Segment Perimeter Calculator?

The formulas are exact for an ideal circle, subject to ordinary floating-point arithmetic. Real accuracy depends on measurement quality, correct arc selection, consistent units, and whether the profile is truly circular. Displaying more decimal places does not create accuracy absent from the original measurements.

Related calculators

Browse all calculators in this category

Editorial review

Author: JD

Sources

Enable JavaScript to use interactive calculators.