Frustum Volume Calculator — Calculate volume for boxes, tanks, and 3D spaces

This Frustum Volume Calculator finds the cubic volume and liquid-capacity equivalent of tapered cones, pyramids, rectangular tanks, hoppers, planters, and prismoids. Choose the geometry that describes the object, enter dimensions in one consistent unit, and use the live end-area and average-area results to audit the calculation.

How to use

Start with Calculation mode. Choose Similar ends from base areas when you already know the two areas and the end shapes are geometrically similar. Choose Conical frustum for two circular ends connected by a straight taper. Choose Similar rectangular ends only when the lower and upper rectangles have the same aspect ratio. Choose General rectangular prismoid when corresponding rectangular length and width dimensions taper by different proportions.

Select the Length unit used by every linear measurement. In area mode, Lower base area and Upper base area are interpreted in that selected unit squared. Enter Perpendicular height as the shortest distance between the end planes; do not enter a sloping wall length.

For a conical frustum, use Circular measurement to identify whether Lower radius or diameter and Upper radius or diameter contain radii or diameters. For similar rectangles, enter Lower length, Lower width, Upper length, and Upper width. The calculator checks their aspect ratios and directs incompatible shapes to prismoid mode.

In General rectangular prismoid mode, enter both pairs of end dimensions. Leave Midsection area blank when length and width change linearly; the calculator derives the halfway area. If a reliable area was measured halfway between the ends, enter it to use that value in the prismoidal formula.

Read Frustum volume first, then inspect liters, US gallons, Imperial gallons, both end areas, and Average cross-section. The displayed formula identifies the model used. As an audit, multiply average cross-section by height and confirm that it reproduces the volume. Use Reset to defaults to restore the area-based demonstration. For real tanks, adjust the ideal result separately for wall thickness, fittings, freeboard, and unusable space.

Formula

For parallel, similar end faces with areas $A_1$ and $A_2$ and perpendicular height $h$: $$V=\frac{h}{3}\left(A_1+A_2+\sqrt{A_1A_2}\right)$$ For a conical frustum with radii $R$ and $r$: $$V=\frac{\pi h}{3}\left(R^2+Rr+r^2\right)$$ When diameters $D$ and $d$ are entered: $$V=\frac{\pi h}{12}\left(D^2+Dd+d^2\right)$$ For a rectangular prismoid with midpoint area $A_m$: $$V=\frac{h}{6}\left(A_1+4A_m+A_2\right)$$ When corresponding length and width dimensions change linearly: $$A_m=\left(\frac{L_1+L_2}{2}\right)\left(\frac{W_1+W_2}{2}\right)$$ All linear dimensions must use one unit. The result uses that unit cubed.

Step by step

Worked audit — similar rectangular frustum

Given a lower end of 6 m by 4 m, an upper end of 3 m by 2 m, and perpendicular height 4 m:

  1. Check similarity: 6/4 = 1.5 and 3/2 = 1.5, so the aspect ratios match.
  2. Calculate the lower area: A1 = 6 × 4 = 24 m².
  3. Calculate the upper area: A2 = 3 × 2 = 6 m².
  4. Calculate the geometric mean: √(24 × 6) = √144 = 12 m².
  5. Add the area terms: 24 + 6 + 12 = 42 m².
  6. Multiply by height and divide by three: V = 4 × 42 / 3 = 56 m³.
  7. Audit with average cross-sectional area: 56 / 4 = 14 m².
  8. Convert capacity: 56 m³ × 1,000 = 56,000 L.
  9. US gallons: 56,000 / 3.785411784 ≈ 14,793.64 US gal.
  10. Imperial gallons: 56,000 / 4.54609 ≈ 12,318.36 Imp gal.

Comparison audit — general rectangular prismoid

For 6 m by 4 m and 4 m by 3 m ends over 4 m, the aspect ratios are 1.5 and 1.3333, so the similar-frustum formula is inappropriate. The derived midpoint dimensions are 5 m and 3.5 m, giving Am = 17.5 m². Then V = 4(24 + 4 × 17.5 + 12)/6 = 70.6667 m³. This demonstrates why geometry selection changes the answer.

Detailed calculation guide

AI Overview: A frustum is the portion of a cone or pyramid between two parallel cross-sections. Its volume depends on the perpendicular height and the areas of the two ends, but the correct equation depends on whether those ends are similar. This calculator handles true conical or pyramidal frustums, similar rectangular ends, and more general rectangular prismoids while also converting geometric volume to liters and gallons.

Featured Snippet: To calculate the volume of a true frustum, multiply the perpendicular height by the sum of the lower area, upper area, and geometric mean of those areas, then divide by three. In symbols, the result is h(A1 + A2 + √(A1A2))/3. The end faces must be parallel and similar.

A frustum is created when a plane parallel to the base cuts the pointed end from a cone or pyramid. The remaining solid has two parallel end faces. Those faces may be circles, squares, rectangles, or another pair of similar shapes. Similar means that corresponding lengths share one scale factor; it does not merely mean that both ends have the same general label, such as “rectangle.” A 6 by 4 rectangle and a 3 by 2 rectangle are similar because both dimensions were halved. A 6 by 4 rectangle and a 4 by 3 rectangle are not similar because their aspect ratios differ.

The calculator separates four geometries because one attractive-looking universal shortcut would be mathematically misleading. Similar-ends mode accepts already calculated base areas. Conical mode calculates those areas from radii or diameters. Similar rectangular mode verifies the aspect ratios before using the standard frustum equation. General rectangular prismoid mode uses the prismoidal formula and a midpoint section, accommodating independent linear changes in length and width.

The perpendicular height is the shortest distance between the parallel ends. It is measured at right angles to their planes. A sloping wall, generatrix, or diagonal edge is normally longer and cannot replace h. For an upright tank the perpendicular height may look vertical; for a tilted or oblique solid it may not. Orientation in a room does not define the mathematical height—the relationship between the parallel planes does.

The area-based formula works because cross-sectional linear dimensions of a true pyramidal or conical frustum vary proportionally between the ends. Cross-sectional area therefore changes quadratically along the height. The square-root term is the geometric mean of the end areas and captures that curvature. Simply multiplying height by the arithmetic mean of the end areas ignores it and is generally not exact.

For circular ends, A1 and A2 equal πR² and πr². Substitution produces πh(R² + Rr + r²)/3. When measurements are diameters, each radius is half a diameter, so the coefficient changes and the denominator becomes 12. The calculator performs this distinction explicitly. Selecting diameter while entering radius values makes the computed volume one quarter of the intended result; selecting radius while entering diameters makes it four times too large.

Rectangular taper deserves special care. If lower and upper rectangles have equal aspect ratios, their areas can enter the ordinary frustum equation. If corresponding lengths and widths change linearly but by different proportions, the solid is better treated as a rectangular prismoid. Its exact volume is h(A1 + 4Am + A2)/6, where Am is the area halfway between the ends. When no measured midpoint area is entered, this tool derives Am as the product of the average corresponding lengths and average corresponding widths.

That derived midpoint is valid only when the relevant edges or dimensions change linearly from one end to the other. Curved side walls, bulging panels, stepped construction, internal ribs, irregular transitions, and off-center openings can make the true midpoint different. If a reliable halfway measurement is available, entering it directly improves the geometric model, although one midpoint still cannot describe every irregular body.

Equal end areas provide a useful boundary check. If A1 equals A2, the similar-end formula reduces to ordinary prism volume, Ah. Equal circular radii therefore produce cylinder volume, while equal rectangular dimensions produce box volume. If one similar end shrinks to zero area, the equation reduces to pyramid or cone volume, Ah/3. These limiting cases are valuable tests for a spreadsheet, drawing calculation, or custom implementation.

Common Mistakes

  • Using slant height instead of the perpendicular distance between the parallel faces.
  • Mixing feet with inches, meters with centimeters, or any other unmatched units before applying the formula.
  • Entering diameter values while radius is selected, or radius values while diameter is selected.
  • Applying the similar-area equation to rectangular ends with different aspect ratios.
  • Using outside tank dimensions when the required quantity is internal capacity.
  • Treating US gallons and Imperial gallons as interchangeable; one Imperial gallon is larger.
  • Rounding converted dimensions or end areas before the final calculation.
  • Assuming total geometric capacity equals safe operating or fillable capacity.

A unit-cubing mistake can be dramatic. One foot is 12 inches, but one cubic foot is 12³, or 1,728, cubic inches. The same principle governs metric conversions: one cubic meter is 1,000 liters, whereas one cubic centimeter is one milliliter. Convert all lengths to one unit first, calculate areas in that unit squared, and report volume in that unit cubed. The capacity conversions in this calculator are derived from the selected unit’s exact or standard meter conversion.

Assumptions

The standard frustum calculation assumes two parallel, similar end faces and straight generators connecting corresponding points. Conical mode assumes circular ends sharing the geometry of a truncated cone. Similar rectangular mode assumes a common aspect ratio and proportional placement. Prismoid mode assumes parallel ends and either a representative measured midpoint or linearly changing corresponding length and width. Every input is treated as an ideal geometric measurement with negligible uncertainty.

The tool allows either end to be larger. Labels such as lower and upper identify the faces; they do not affect the formula because the equations are symmetric in A1 and A2. A zero-area end is permitted where it represents a mathematical apex. Perpendicular height must remain greater than zero because a zero-height object encloses no three-dimensional space and does not define a useful capacity calculation.

Limitations

Real tanks and fabricated parts rarely match nominal geometry perfectly. Wall thickness reduces internal dimensions. Welds, rounded corners, liners, insulation, baffles, pumps, pipes, valves, sediment, and support structures displace usable liquid. Flexible containers may deform as they fill. Manufacturing tolerances and field measurements add uncertainty, particularly because errors in circular radius are squared when area is computed.

This calculator does not model horizontal fill depth in a partially filled tapered vessel. Partial volume requires locating the liquid surface and integrating or applying a geometry-specific segment formula. It also does not determine surface area, material quantity, center of mass, hydrostatic pressure, structural loading, flow rate, or drain time. Those are related engineering questions with different inputs and assumptions.

Practical Applications

Typical uses include estimating the internal capacity of a tapered planter, hopper, bin, mold, bucket, cup, transition duct, truncated-pyramid tank, architectural feature, excavation, or fabricated enclosure. Students can compare a full cone with the smaller cone removed from its tip. Designers can use the end-area output to verify drawings. Construction estimators can translate ideal volume into material quantities after separately applying compaction, waste, bulking, and safety factors.

A rectangular planter with larger top dimensions than bottom dimensions often fits prismoid mode because its length and width may taper independently. A square-pyramid frustum belongs in similar rectangular mode when both side lengths change by the same factor. A round vessel belongs in conical mode only when its side profile is straight between the circular ends; a barrel-like curved profile requires another model or measured cross-sections.

Tips

  • Measure internal dimensions when calculating storage or liquid capacity and external dimensions when calculating occupied envelope volume.
  • Take several measurements around imperfect circular or rectangular ends and document how an average was selected.
  • Keep full precision through intermediate areas and conversions, rounding only the reported answer.
  • Sketch and label both parallel ends before choosing a calculation mode.
  • Compare the result with bounding prisms: volume should normally lie between h times the smaller end area and h times the larger end area.
  • Record whether a circular value is a radius or diameter directly beside the measurement.

Interpretation

The primary result is expressed in the selected unit cubed. Lower and upper end areas are shown in the corresponding squared unit. Average cross-sectional area is volume divided by perpendicular height, not necessarily the arithmetic mean of the end areas. Multiplying that displayed average by height reconstructs the reported volume and provides an independent audit path.

Capacity equivalents express the same ideal volume in liters, US liquid gallons, and Imperial gallons. They do not imply that the object is watertight, food-safe, pressure-rated, or fillable to its rim. For operations, distinguish gross capacity, nominal capacity, working capacity, and usable capacity. Freeboard and minimum operating levels can make usable capacity materially smaller than the geometric figure.

A basic reasonableness interval is h times the smaller end area through h times the larger end area. A positive frustum with straight taper should fall within these bounds. If a reported value falls outside them, investigate units, height definition, or geometry selection. The exact result may be closer to one bound depending on how quickly cross-sectional area changes along the height.

Related Formulas

The ordinary prism or box equation is V = Ah. A cylinder uses V = πr²h. A pyramid or cone uses V = Ah/3. A frustum can also be calculated as the volume of a complete cone or pyramid minus the volume of the smaller, similar solid removed from its apex. That subtraction method is useful when full and removed heights are known, but it can amplify rounding error when two large, nearly equal volumes are subtracted.

The average-end-area estimate is h(A1 + A2)/2. It is convenient for quick earthwork approximations but is not generally identical to the prismoidal or true-frustum result. For a true frustum with unequal ends, the arithmetic-mean estimate exceeds the standard result because the geometric mean cannot exceed the arithmetic mean. Understanding that direction of bias is more informative than treating both formulas as interchangeable.

Best Practices

Choose geometry from physical evidence rather than the desired answer. Confirm parallel end planes, inspect whether side edges are straight, and test rectangular aspect ratios. Convert raw measurements into a consistent unit set before calculating. Preserve source measurements and assumptions in a drawing or worksheet so another person can reproduce the result. For consequential fabrication, procurement, or capacity decisions, compare the calculation with CAD, calibrated fill testing, manufacturer data, or an independent engineering review.

Measurement precision should match the decision. Reporting ten decimal places from dimensions measured with a tape does not create ten-place accuracy. A practical uncertainty check recalculates volume using plausible high and low dimensions. Circular tanks deserve particular attention because a small radius error affects squared terms. Report a sensibly rounded estimate together with its measurement basis.

When NOT to use this calculator

Do not use the true-frustum modes for spherical sections, barrels, domes, curved hoppers, offset transitions without similar sections, twisted shapes, or vessels whose end planes are not parallel. Do not use full geometric volume as a certified pressure-vessel capacity, trade measurement, dosing value, structural design input, or hazardous-material limit. Regulatory and safety-critical applications require applicable standards, calibrated methods, and qualified professional review.

Do not use the capacity output to infer how much material to purchase without considering density, compaction, expansion, voids, waste, and delivery increments. Volume alone does not determine mass. Likewise, a liquid volume does not determine pressure; pressure depends on fluid density, depth, acceleration, and vessel conditions.

Real-world examples

A conical hopper with radii 1.5 meters and 0.5 meters and a perpendicular height of 3 meters encloses approximately 10.2102 cubic meters. A tapered box with similar 6-by-4 and 3-by-2 meter ends over 4 meters encloses 56 cubic meters. A non-similar transition from 6 by 4 meters to 4 by 3 meters uses a derived midpoint of 17.5 square meters and produces about 70.6667 cubic meters over a four-meter height.

For a small planter measured in centimeters, the numerical cubic-centimeter result may look large while the liter equivalent remains intuitive because 1,000 cubic centimeters equal one liter. For an excavation measured in feet, cubic yards can be obtained by dividing cubic feet by 27. These examples show why the unit attached to a number is part of the result, not decorative notation.

Comparison and educational perspective

The area formula is compact and elegant, but it carries stronger similarity assumptions than its short appearance suggests. The prismoidal formula requests more geometric information through a midpoint section and therefore handles a broader class of straight-edged transitions. The average-end-area method is simpler but typically approximate. Selecting among them is a modeling decision: the best equation is the one whose assumptions most closely describe the measured object.

The Frustum Volume Calculator is most useful as a transparent audit tool. It exposes both end areas, average cross-sectional area, selected formula, cubic volume, and capacity conversions so the answer can be checked rather than merely accepted. For boxes, tanks, and three-dimensional spaces, trustworthy calculation begins with identifying the shape correctly, measuring perpendicular height, keeping units consistent, and separating ideal geometry from real usable capacity.

Beginner: square-pyramid frustum from areas

65.33333333 m³

The end areas have geometric mean 15 m², so V = 4(25 + 9 + 15)/3 = 65.33333333 m³.

Intermediate: conical hopper using radii

10.21017612 m³

Using πh(R² + Rr + r²)/3 gives 3.25π, or approximately 10.21017612 cubic meters.

Advanced: similar rectangular tank

56 m³

Both rectangles have aspect ratio 1.5, so their 24 m² and 6 m² areas can use the standard similar-frustum formula.

Edge case: cone with a zero-radius end

314.1592654 cm³

With one circular end reduced to an apex, the conical-frustum equation becomes ordinary cone volume π × 5² × 12 / 3.

Real-world: non-similar rectangular transition

70.66666667 m³

The derived midpoint is 5 by 3.5 meters, or 17.5 m². The prismoidal formula then gives 4(24 + 70 + 12)/6.

Diameter entry for a tapered round vessel

175.9291886 ft³

The calculator applies the diameter form πh(D² + Dd + d²)/12, avoiding a manual conversion to 4-foot and 2-foot radii.

Frequently asked questions

What is a frustum?

A frustum is the part of a cone or pyramid remaining after a plane parallel to the base removes the apex. It has two parallel, similar end faces connected by straight tapered sides.

How do I calculate frustum volume?

For similar parallel ends, use V = h(A1 + A2 + √(A1A2))/3. Enter the perpendicular height and the two end areas, keeping every measurement in a consistent unit system.

Which height should I enter in the Frustum Volume Calculator?

Enter the perpendicular distance between the two parallel end planes. Do not enter a sloping wall, diagonal edge, or side measurement because those lengths normally exceed the required height.

Can this calculator find the volume of a tapered rectangular tank?

Yes. Use similar rectangular ends when both rectangles have the same aspect ratio. If length and width change by different proportions, use general rectangular prismoid mode instead.

What is the difference between a radius and a diameter?

A radius runs from the center of a circle to its edge, while a diameter crosses the full circle and equals twice the radius. Selecting the wrong measurement type changes calculated volume by a factor of four.

Can either end be the larger base?

Yes. The volume equations are symmetric in the two end areas, so swapping lower and upper values does not change the result. The labels simply help you match measurements to the physical object.

What happens when both ends have equal dimensions?

Equal end dimensions eliminate the taper. The frustum formula then reduces to V = Ah, giving ordinary cylinder volume for circular ends or prism and box volume for rectangular ends.

Can one end have zero area?

Yes. A zero-area end represents an ideal apex, and the equation reduces to the familiar cone or pyramid formula V = Ah/3. Both end areas cannot be zero for a meaningful solid.

Why is averaging the two end areas not always exact?

Cross-sectional area usually changes quadratically rather than linearly along a true frustum. The exact similar-end formula includes √(A1A2), while the simple arithmetic average omits that geometric behavior.

What is a rectangular prismoid?

It is a solid bounded by parallel end sections whose intermediate geometry can be represented by a midpoint area. For linearly changing rectangular dimensions, the prismoidal formula gives the exact ideal volume.

Are US gallons and Imperial gallons the same?

No. One US liquid gallon equals 3.785411784 liters, while one Imperial gallon equals 4.54609 liters. The calculator displays both conversions separately to prevent an ambiguous gallon result.

Does geometric tank volume equal usable capacity?

Not necessarily. Wall thickness, freeboard, fittings, rounded corners, internal equipment, minimum operating levels, deformation, and unusable space can all reduce real working capacity.

How can I check whether the result is reasonable?

Multiply height by the smaller and larger end areas. For an ordinary positive taper, volume should lie between those bounds. You can also multiply the displayed average cross-section by height.

Related calculators

Browse all calculators in this category

Editorial review

Author: JD

Sources

Enable JavaScript to use interactive calculators.