Paint Coverage Calculator

Buying too little paint means a mid-project store run; buying far too much wastes money and creates leftover cans. This Paint Coverage Calculator estimates gallons from room length, width, wall height, coats, label coverage, door and window openings, and an optional waste buffer so DIY painters and landlords can plan purchases before opening the first can.

How to use

  1. Measure room length, width, and wall height in feet.
  2. Count door and window openings you have not already excluded from your tape measure.
  3. Enter coats — use 2 for most color changes, 1 for a similar-shade refresh.
  4. Enter coverage per gallon from the paint can label (often 250–400 sq ft).
  5. Add a waste buffer of about 5–15% for cut-ins, texture, and touch-ups.
  6. Read gallons needed, then round up to the next practical can size at the store.
  7. If painting the ceiling too, add length × width as a separate area outside this wall estimate.

Formula

$$\mathrm{gallons}=\frac{\max(2(L+W)H - 21d - 15w,\,0)\cdot c\cdot(1+\frac{b}{100})}{r}$$

Step by step

Worked example — 14×12 ft room, 8 ft ceilings, 2 doors, 2 windows, 2 coats, 350 sq ft/gal, 10% buffer.

  1. Perimeter = 2×(14+12) = 52 ft.
  2. Gross wall area = 52×8 = 416 sq ft.
  3. Openings = 2×21 + 2×15 = 72 sq ft.
  4. Net area = 416 − 72 = 344 sq ft.
  5. With coats = 344×2 = 688 sq ft.
  6. With 10% buffer = 688×1.10 = 756.8 sq ft.
  7. Gallons = 756.8 ÷ 350 ≈ 2.16 gallons. Buy roughly 2.25–3 gallons depending on packaging.

Second check — 10×10×8 room, 1 door, 1 window, 1 coat, 400 sq ft/gal, 5% buffer: Perimeter 40, gross 320, openings 36, net 284, adjusted 298.2, gallons ≈ 0.75.

Detailed calculation guide

Wall area starts from the room perimeter times height: perimeter = 2 × (length + width), gross wall area = perimeter × height. Subtract typical door and window allowances (defaults here use about 21 sq ft per door and 15 sq ft per window) to get net paintable area. Multiply by coats because a primer-plus-finish or two finish coats multiplies surface demand. Divide by the manufacturer coverage rate (often 250–400 sq ft per gallon depending on surface and product) to get gallons, then apply a waste buffer for cut-ins, texture, and touch-ups.

Coverage rates on the can assume a smooth, sealed surface. Porous drywall, unfinished wood, or dramatic color changes often need more product than the label midpoint. Always round purchases up to the next practical can size after reviewing store packaging (quarts vs gallons vs 5-gallon pails).

This tool is for planning, not a substitute for measuring every opening precisely or reading the technical data sheet for sheen, VOC, and recoat times.

Practical planning tips: buy all cans from the same batch/lot when color matching matters, stir thoroughly, and finish a full wall before stopping for the day to reduce lap marks. Sheen choice (flat, eggshell, satin, semi-gloss) does not change the gallon math but does affect washability and how visible roller texture appears under raking light. Primer is often sold separately—if you need primer, treat it as an additional coat with its own coverage rate rather than assuming finish paint alone will hide stains or raw drywall. When changing from dark to light, expect more coats than the calculator’s default two. Record your net square footage in project notes so touch-up purchases later use the same assumptions.

Standard bedroom

≈2.16 gallons

Default worked example with openings and buffer.

Small office, one coat touch-up

≈0.75 gallons

Similar color refresh with higher coverage.

Large living room, two coats

≈3.9+ gallons

Lower coverage and higher buffer for textured walls.

Frequently asked questions

How do I calculate how much paint I need?

Find net wall area, multiply by coats, divide by the label’s square feet per gallon, then add a small buffer for waste and touch-ups.

Should I subtract doors and windows?

Yes if your tape measure included full walls. This calculator subtracts typical door and window allowances so you do not overbuy.

How many coats should I enter?

Two coats are common for a noticeable color change. One coat may work for a similar shade over a sealed surface; three can be needed for stark changes or dark over light.

What coverage rate should I use?

Use the manufacturer range on the can. Smooth walls near the high end; textured or porous surfaces near the low end.

Does this include the ceiling?

No—this version estimates vertical wall area only. Add ceiling length × width as a separate area if you are painting the ceiling too.

Why add a waste buffer?

Cut-ins, roller texture, spills, and future touch-ups consume extra paint. A 5–15% buffer reduces mid-project shortages.

Browse all calculators in this category

Editorial review

Author: JD

Sources

Enable JavaScript to use interactive calculators.