PSI to inHg Converter — Convert units with exact factors and live results
Enter a pressure in pounds per square inch (psi) to express the same pressure in inches of mercury (inHg). This converter uses the conventional 0 °C mercury-column factor: 1 psi = 2.0360206576 inHg. It preserves the reference type of your reading, so a gauge-pressure input remains a gauge-pressure result.
How to use
- Enter a finite value in Pressure (psi). Decimal and negative values are allowed; use a negative value only when the source reading is meaningfully below its gauge reference. 2. Read Equivalent pressure in inHg, calculated with the displayed 0 °C convention. 3. Keep the same reference type when documenting the result: psi gauge converts to inHg gauge, while psi absolute converts to inHg absolute. Empty, non-numeric, NaN, and infinite entries should be corrected rather than interpreted as pressure values.
Formula
Step by step
For an atmospheric-pressure-scale example, start with 14.6959 psi. Multiply by the fixed conversion factor: 14.6959 × 2.0360206576 = 29.921155982024 inHg. Rounded to this calculator's five displayed decimal places, the result is 29.92116 inHg. As a fractional check, 0.5 × 2.0360206576 = 1.0180103288 inHg, displayed as 1.01801 inHg. The boundary case 0 psi gives exactly 0.00000 inHg. If -1 psi is a valid gauge reading in context, it converts to -2.03602 inHg and remains gauge-referenced.
Detailed calculation guide
This PSI to inHg converter changes the unit used to report pressure; it does not change the physical pressure or whether a reading is gauge or absolute. It uses the stated conventional factor for inches of mercury at 0 °C. That convention matters because a mercury-column unit depends on the density of mercury, which varies with temperature.
Variables and units
The input is Pressure (psi), where psi means pounds-force per square inch. The output is inHg, or inches of mercury. The calculation uses 2.0360206576 inHg per psi. Negative inputs are accepted because they can represent gauge pressure below the chosen reference pressure. A negative gauge reading is not automatically a negative absolute pressure.
| Input pressure | Calculation | Converted pressure |
|---|---|---|
| 0.5 psi | 0.5 × 2.0360206576 | 1.01801 inHg |
| 1 psi | 1 × 2.0360206576 | 2.03602 inHg |
| 14.6959 psi | 14.6959 × 2.0360206576 | 29.92116 inHg |
Interpreting the result
The displayed value is a unit equivalent. It should not be read as extra accuracy in the original measurement. For example, a tire gauge reading rounded to the nearest whole psi does not become a five-decimal-place measurement merely because the converted result shows five decimals.
This conversion is useful when comparing specifications, instrument displays, weather-related pressure references, laboratory notes, or HVAC documentation that use different units. Before comparing two readings, confirm whether each is gauge pressure or absolute pressure. Converting psi gauge to inHg gauge is appropriate; converting it to inHg absolute would require adding the applicable reference pressure first.
Practical use and related formulas
The direct relationship is linear, so doubling psi doubles inHg. The reverse calculation is inHg divided by 2.0360206576. A cross-check can also be made through kilopascals: the commonly tabulated values are about 6.894757 kPa per psi and 3.386389 kPa per inHg at 0 °C. Their ratio gives the displayed psi-to-inHg factor, subject to the published precision of those values.
Common mistakes
- Using 2.04 when the application needs more digits than that rounded shortcut provides.
- Treating psi gauge and psi absolute as interchangeable.
- Comparing an inHg value based on one mercury-temperature convention with a value based on another convention.
- Treating conversion digits as evidence that the sensor or gauge was equally precise.
- Entering a missing, non-numeric, infinite, or undefined value instead of a finite pressure reading.
Assumptions and limitations
This tool uses a fixed 0 °C inHg convention and reports a mathematical unit conversion only. It does not compensate for local temperature, instrument calibration, altitude, fluid-column conditions, or measurement uncertainty. Use the unit convention specified by the equipment, calibration certificate, regulation, or technical standard when it differs from this page's convention.
Do not use this calculator to infer vacuum quality, weather conditions, system safety, or compliance without the correct reference type and measurement procedure. For calibrated work, retain the original instrument resolution, uncertainty statement, and convention alongside the converted value.
One psi reference value
2.03602 inHg
A 1 psi input is a convenient check of the fixed conversion factor.
Fractional pressure reading
1.01801 inHg
This example shows that decimal pressure readings convert directly without changing their reference type.
Atmospheric-pressure-scale example
29.92116 inHg
This is a unit conversion example only; whether the input is absolute or gauge must be known separately.
Zero-pressure boundary
0.00000 inHg
Zero converts exactly to zero under the linear relationship.
Negative gauge-pressure example
-2.03602 inHg
A negative result can be meaningful for gauge pressure below its reference; it should not be assumed to be absolute pressure.
Frequently asked questions
How many inches of mercury are in 1 psi?
Using this converter's 0 °C mercury-column convention, 1 psi equals 2.03602 inHg when rounded to five decimal places.
Why do psi-to-inHg factors sometimes differ slightly?
Inches of mercury are convention-dependent because mercury density changes with temperature, and published factors may also be rounded differently.
Can I convert psi gauge directly to inHg?
Yes. Convert psi gauge to inHg gauge with the same factor, but do not present that result as an absolute-pressure reading.
Is 14.6959 psi equal to 29.92 inHg?
Approximately. With the factor used here, it is 29.921155982024 inHg before rounding, or 29.92116 inHg displayed.
Does converting pressure make the measurement more precise?
No. The conversion preserves the information in the source reading; extra displayed digits do not improve instrument resolution or calibration.
Browse all calculators in this category
Editorial review
Author: JD
Sources
Enable JavaScript to use interactive calculators.